One thing I just thought of HG. On the vertical surfaces don't put the paint on too thick
especially if the weather is hot. It takes a while for the paint go off and the hot weather
will dry the surface of the paint and allow the sub-surface to drop, so thin coats are the
way to go. It doesn't matter so much on the flat surfaces, but be wary.
I'm looking at touching up the bare spots on my cabin sides with interprotect under coat and then rolling single pack over the top a light grey colour. And same with the decks but with true grit added.
Refitted a staunchion that was beyond wobbly. Reconnected the groovy old compass illumination which looks cool now it's dark. Anna started on the dodger patch for a hole worn by the sail cover brushing across it for the 6 years before we got her - the sail cover has already got a new section!
We're on a roll, what shall we do tomorrow?
Final sand with 400 Grit . Rolland tip the last coat on Saturday morning .
Ill start sanding the pepping the deck tomorrow. Its no Rolls Royce paint job but it will do me.
Rolled and tipped both side with there final coat .
Yesterday I started sanding the deck prepping it for non skid and edges .
Probably the same colour as Mrs Sam Sturdy did
Not so much what am I doing to my boat more having done. In the middle of a refurbishment inside. Replacing the astro turf mottles came out decorated in with grey marine liner. New perspex in hatches and windows. Replacing some water dammaged ply. Fitting two extra barlow 25 st winches further aft so they can be used while still at the helm.
Had the riggers down today to go over the rig which I get done every 12 month. I timed it just right as I heard a bang and noticed the main halyard dropped about 20mm while sailing on Saturday, but just assumed the halyard must have slipped in the clutch. When the rigger checked the masthead he found the main halyard pulley at the top of the mast had calapsed. He also dissacembled the jib furler, released all the rigging screws,regreased all the threads and retensioned the entire rig. He is machining up a new solid block for the masthead tonight and will be back to fit it tomorrow. All should be good for another 12 months.
spent the last two days on my knees sanding and priming above the rub rail and deck also sanded the teak trim.
I Usually use Sikens light oak and works well
This time I might use west system 207/105 resin three coats sand and three coats of varnish. My theory is I wont have to sand any teak just the varnish . I hate loosing teak by sanding every time when it need redoing it
Well it was not my boat but my mates alloy Cole 42. I gave him a hand to sail her down from Lane Cove to her new home in Greenwell Point last night. Damn this boat was good buy! Way too big for my needs but this is a seriously good buy. Hate to guess what this boat cost to build. We encountered Wild Oats as we left the cove and I had to put up with my mates **** eating grin all the way home!
Should be a good boat when hes done Ramona
Did some deck sanding and then as Im moving winches further aft, so drill and fitted some teak plugs before any more sanding
A coat of paint to deck and gunwale rubbing strip again a never ending task, need to do an injector replacement to the 27hp Kubota, repair the wear to the Bimini Cover, just a usual day at the boat.
Unfortunately on Vic we are still getting 4 seasons in a day slowly getting warmer
One day it's good to paint but over night it will rain
Then rain for the next few days
8 coats so far its a sanding day tomorrow
I pulled her out of the water in preparation to give her a big big birthday.
Waiting for Ben to get his boat out.
Bundaberg Slipways' very innovative slipway travel lift.
I will be going into the left hand corner in front of the big anchor.
The rotten rudder (not quite). The chunk out of the back is where a filthy worm got in.
Not bad after being in the water for 3 years. The anti foul is Altec No. 5
Even with all the barnies it is still a sleek looking keel.
She will be here for 2 or 3 days before going into the cradle.
Budget for this slipping is $5,000 which includes re rigging. All donations gratefully accepted.
Over the last few weeks I have been repairing my Autohelm. When I purchased 'Vamoose', the autopilot worked intermittently and performed the odd 'crazy Ivan'. This got worse over the next couple of sails until it didn't work at all.
When I pulled it apart, I found that the belt had perished and fallen apart. I found a new belt on an online auction site, waited for it to ship from the States and now I have a perfectly working Autohelm.
It amazes me how well this piece of 30 year old technology works. On the weekend it kept us on course for over 3 hours and 17 nautical miles on our way back from Tangalooma. The wind came from all points on our beam and often gusted to 20 knots.